FABRICATION ~ CHIP TURNING ~ CNC

 Manufacturer: 

 Giddings & Lewis 

Model: 

 570-FUAR 

Number of Columns: 

 (2) each w/7" & 2-1/2" Spindles 

Spindle speeds: 

 2 - 400 rpm 

Spindle feeds: 

 0.005" – 0.250" & 0.010" – 0.500" 

Travel range on key: 

 14" - 510" 

Max tracing range: 

 108" 

Spindle travel: 

 60" 

Spindle taper: 

 #7 Morse Taper 

Max between spindles: 

 640" 

Machine #1 and #2 travel: 

 504" each 

Floor Space dims: 

 335" W x 732" L 

This is two 7" dia spindle machines on one runway, one on each end. Further, each has both a 7" dia main spindle and a 2-1/2" Aux spindle. 

There is an Underarm spindle support system that supports the spindle on each of the machines the full 60" of main spindle travel. 

This machine is equipped as follows: 

• 7" dia main Spindle providing 60" of spindle travel 

• 2-1/2" Auxiliary spindle 

• #7 Morse Taper Spindle – Part No. 26898 (Special for Tracer Machine) 

• Digital Readouts on each spindle 

• Headstock unit – General 

• Headstock – Section covering specific parts for 570 

• Headstock – Additions & Omission for Tracer Machine 

• Tracer (for 108" max Tracing Range) 

• 60" Spindle travel – Controlled parts for machine with Tracer 

• Ram Guide & Underarm Unit 

• Ram Guide & Underarm Unit (Tracer / Additions & Omissions) 

• Spindle Feed 

• Column Base General "F" 

• Column Base (Tracer) Additions & Omissions 

• Column Base Specific – Formica Wear Plates 

• Milling Feed 

• Milling Feed (Tracer) Additions & Omissions 

• Column – "FUAR" with Tracer 

• Incremental Trip (for two columns) 

• End Support "F" 

• Scales and Adjustable Verniers with Horizontal Vernierscope 

• Feed Reel 

• Electrical Parts "FUAR" with Tracer 

• Collision Switch 

• Hydraulic Cylinders (Headstock & Spindle Feed) 

• Hydraulic Cylinders (Column Base "F" Type) 

• Clamp Bearings 

• Torque Motors (End Support) 

• Note Plates 

• 120" Column 

• 640" Runway with Hardened Ways – Mounted on Leveling Jacks 

• 120" End Support Column 

• 96" End Support Runway 

• 11 Sections Floor Plate 14" x 4' x 12' Making total Floor Plate foot print 14" thick x 44' long x 12' wide 

• General Electric Controls including Tracer Control 

Accessories 

• Shaping & Slotting Attachment – (Underarm) 

• Spindle Support – (Underarm) 

• 90º Angular Milling Attachment – (Underarm) 

• Offset Milling Attachment – (Underarm) 

• Additional Parts Required when CFFH is used on (Underarm) Spindle Support 

• Coolant Pump & Piping 

• 48" Continuous Feed Facing Head 

• Telescopic Tools for 48" Continuous Feed Facing Head 

• Handwheel Arrangement for 48" Continuous Feed Facing Head 

• Angle Plate – 30" x 48" x 24" (16 units) 

• Draw Key 

• #12 Stub Boring Tool Set 

• #17 Adjustable Fly Cutters 

• Giant 4 #4 Adjustable Block Cutters 

• Giant 4 #5 Adjustable Block Cutters 

• Giant 4 #6 Adjustable Block Cutters 

• Giant 4 #7 Adjustable Block Cutters 

• Giant 4 #8 Adjustable Block Cutters 

• #774-10 7" Dia. X 156" long Boring Bar 

• Adjustable extension Type Boring & Facing 

• 6" Dia x 120" long Boring Bar 

• Adjustable extension type Boring & Facing

Still installed, this extraordinary machine may be inspected on request.  

MAKE OFFER:  AS IS WHERE IS